Desk Gear Hub logo Desk Gear HubBetter desks, longer sessions
Monitors and Lighting

Vertical Second Monitor and What Portrait Mode Fixes

I rotated my old 27 inch panel to portrait on a Thursday because a video told me it was free productivity, and I rotated it back nineteen days later. Nothing about it was broken.

A desk with a landscape gaming monitor beside a second monitor rotated into portrait orientation on a low mounted arm

I rotated my old 27 inch panel to portrait on a Thursday because a video told me it was free productivity, and I rotated it back nineteen days later. Nothing about it was broken. Chat was readable, patch notes fitted on one screen, and I could see a whole code file without scrolling. The problem was that by the third evening of a long session I had a specific ache at the base of my skull that I had not had before, and it was coming from looking up.

Portrait mode is one of those changes that is genuinely useful and almost always done with the wrong panel in the wrong place. The question is not whether a vertical monitor helps. It is which panel you rotate and how low you can get the thing, and both of those have numbers attached that nobody mentions in the clip where they spin the screen round and smile.

What rotating a screen does to the geometry

A 16:9 panel keeps its diagonal when you turn it, so the width and height swap. That swap is bigger than people picture.

PanelLandscape, width by heightRotated, width by height
24 inch 16:953.1 by 29.9 cm29.9 by 53.1 cm
24 inch 16:1051.7 by 32.3 cm32.3 by 51.7 cm
27 inch 16:959.8 by 33.6 cm33.6 by 59.8 cm
32 inch 16:970.8 by 39.9 cm39.9 by 70.8 cm

Take the 27 inch row. Rotated, the panel is nearly 60cm tall. A standard desk sits at 72 to 75cm. If the bottom edge of the screen clears the desk surface by even 6cm, which most stands force, the top edge lands at about 138cm from the floor. Seated eye height for an adult of average height is somewhere near 115 to 120cm. You are now reading content 20cm above your eye line, and the top third of a portrait screen is where the clock, the tab bar and the top of every document live.

Looking up is worse than looking down. Your neck has a lot more comfortable range below the horizontal than above it, which is the reason every ergonomics guide puts the top of a landscape screen at or slightly under eye level. Rotating a panel does not change that rule, it just makes it much harder to obey. The same geometry argument runs through the piece on monitor height, and portrait mode is where it bites hardest.

Pixels decide whether it is readable, not inches

The second thing that caught me out was text quality. Rotating a 1920 by 1080 panel gives you 1080 pixels of width. On a 27 inch screen that works out around 81 pixels per inch, and at normal viewing distance the letters look soft and slightly blocky, the way an old office monitor does. The same panel at 1440p gives roughly 109 pixels per inch and reads cleanly.

The width number matters on its own too. A 1080 pixel wide column at 100 percent scaling fits a web page and a chat window side by side with nothing to spare. At 125 percent scaling, which is what most people need to read comfortably at that pixel density, you are down to an effective 864 points of width, and a lot of web layouts start collapsing into their mobile view. That is not always bad, but it means the screen is doing a different job than you imagined.

Mixed orientation setups also expose per display scaling. Windows handles it better than it used to, and it still produces blurry windows when you drag an application between a 100 percent screen and a 125 percent screen without signing out. If you game in fullscreen, expect the occasional alt tab to shuffle your window positions on the vertical screen. It is a small annoyance repeated forty times a week.

The counter take: a 27 inch is the wrong panel to rotate

The advice you will find is to take your spare monitor, whatever it is, and stand it up. The logic is that the panel is already paid for, so any gain is free. I have tried this with three different screens and I think it is backwards. Rotating your largest spare is the version most likely to end up back in a cupboard.

What worked for me was a 24 inch 1920 by 1200 panel, which is the 16:10 row in that table. Rotated it is 51.7cm tall instead of 59.8cm, which buys back 8cm of height, and the extra 120 pixels of width land exactly where a portrait screen needs them. I paid 149 euro for a used one and it has stayed on the desk for seven months, which is longer than anything else I have tested this year.

The other half of the fix is vertical position. Do not align the top edges of your two screens. Align the vertical screen's centre with the centre of your main screen, which means the portrait panel's top edge finishes well above your main screen and its bottom edge drops below desk level unless you mount it beside the desk edge. In practice I set the bottom edge about 4cm above the desk and accept that the very top of the portrait screen is only for things I glance at, not things I read.

If the top quarter of your vertical screen holds anything you read for more than ten seconds, the screen is too tall or mounted too high.

The arm spec people get wrong

You need a mount, not a stand, because almost no included stand rotates and the ones that do cannot drop low enough. Three numbers to check before buying.

Rotation at the plate. The VESA head must turn a full 90 degrees with the screen attached, and ideally 360, since some arms only rotate one way and that direction may put your ports against the wall. Check the plate specification and not the product photo.

Minimum height, not maximum. Arm listings advertise how high they go. For portrait you care about how low. A gas spring arm on a 400mm pole often cannot bring the VESA centre below 30cm above the clamp, which puts a 27 inch portrait panel's top edge right back where it hurt. Look for the quoted lowest position or use a short pole with a desk clamp at the back edge.

Load range, with the bottom end checked. Gas spring arms have a minimum weight as well as a maximum, commonly around 3kg. A light 24 inch panel at 2.6kg will drift upward and not stay where you put it. Either pick an arm rated from 2kg or add the stand plate back on for weight. Mechanical spring arms are fussier to adjust and hold a light panel better. There is more on the stand against arm decision in the comparison of arms and stands.

What it is actually good for at hour four

Here is where I landed after seven months. The vertical screen is not a second gaming display and it is not where your main work lives. It holds things that are tall and scroll: a chat window, a long patch note page, a build log, a reference document, a queue. During a long session the value is that none of those things ever covers the main screen, and alt tabbing out of a fullscreen game at a bad moment is how a lot of evenings go wrong.

It is a poor fit for anything wide. Spreadsheets, timelines, video editing and most game launchers all want horizontal room, and a portrait panel punishes them. If what you actually want is more width, two landscape screens angled inward is the better answer, and the placement for that is covered in the dual monitor positioning guide.

Before you buy anything, test it for a week with the panel you already own. Rotate it, prop it on a box so the bottom edge sits near desk level, and put only chat and documents on it. If you reach for it daily, buy the 24 inch and a mount that goes low. If you do not, you saved yourself a hundred euro and some neck ache.

FAQ

What size monitor is best for vertical use?

A 24 inch panel, and a 16:10 one if you can find it, since 1920 by 1200 rotates into a column wide enough to read without the extra height of a 27 inch screen.

Does a vertical monitor cause neck strain?

It can, because the top of the screen usually sits above eye level and the neck has little comfortable range looking up. Mounting it low enough removes most of the problem.

Can I use a vertical monitor for gaming?

Only for a few arcade and shoot em up titles built for tall screens. Treat it as a space for chat, guides and logs while the game stays on the landscape screen.

Do I need a special arm to rotate a monitor?

You need one whose VESA head rotates 90 degrees and that can be set low. Check the minimum mounting height and the bottom of the weight range, since a light panel will not hold position on an arm rated from 3kg.

OT
Owen Takahara

Owen plays PC games most nights and has worn the legends off four keyboards. He writes about how gear and setup change long online game sessions.

More posts by Owen

More in Monitors and Lighting

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles aotc asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano litemagazines localcommunityhero lustrsazan mariashebets menswheels newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin rwxqsgd5 sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto ankertoto ankertoto